Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
We've noticed the article about How to Install a Bathtub down the page on the internet and figured it made sense to share it with you in this article.
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a moderately hard project. If the old tub is conveniently obtainable, the job can move immediately; if you have to open a wall surface to eliminate the old tub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the new one. Make certain you have qualified on your own for the work and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you may require an expert plumber to make tube connections.
This short article will help you install a new tub in your restroom if you have actually currently bought a new bathtub and don't need to change the plan of your previous water supply pipes.
Your devices and material checklist should make up the following:
Planning for the Installment
Firstly, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is separate the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic because of the restricted access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the tub in the required placement. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water system and examine all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling and securing around the tub ought to wait until the tub has been made use of at the very least once as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Protect the faucet in position with the maker supplied backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type should be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, creating the water to permeate the wall surface between the bath and also the tiling, resulting in complications with dampness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can split rather early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our part about Installing A Bathtub. Thank you for taking a few minutes to read our short article. Enjoyed our write up? Please share it. Let somebody else discover it. We truly appreciate reading our article about Installing A Bathtub.
Excellence awaits, dial! Report this page